CamshaftNow
Industrial Lubrication

Schaeffler: A Practical Guide to Bearings and Lubrication

Schaeffler: A Practical Guide to Bearings and Lubrication
Learn what Schaeffler makes and how to select, lubricate, and maintain its bearings using practical guidance on viscosity, grease, and failure analysis.

A bearing that runs hot after a grease change may be telling you about excess lubricant, contamination, incorrect clearance, or a mismatch in lubricant properties. Schaeffler is a German industrial and automotive supplier known for rolling bearings and related components. For a maintenance engineer, the useful question is not simply who made the bearing; it is how the bearing’s design, operating conditions, and lubrication instructions fit together.

Schaeffler’s bearing brands include FAG and INA. You will encounter them in equipment ranging from industrial gearboxes and electric motors to automotive assemblies. The company also supplies components and systems beyond bearings. Here, I’ll focus on the bearing and lubrication decisions that matter at the workbench.

What the bearing markings tell you

FAG is a familiar name on rolling bearings, while INA is associated with products including needle roller bearings. A rolling bearing carries load through rolling elements, such as balls or rollers, between bearing surfaces called raceways. Different geometries handle radial loads, axial loads, and alignment errors differently; no brand name tells you that a substitute has the right geometry.

Start with the complete designation on the bearing or its packaging. The basic number identifies the bearing type and dimensions, while suffixes can specify features such as internal clearance, seals, cage design, or accuracy. Suffix conventions are manufacturer-specific, so use the Schaeffler catalog for the exact designation rather than assuming another manufacturer’s suffix means the same thing.

Internal clearance is the small amount one bearing ring can move relative to the other before mounting. Fits and operating temperatures change that clearance in service. ISO 5753-1 defines radial internal clearance groups for specified rolling bearings; it does not tell you to choose a larger-clearance bearing for every hot machine. Follow the equipment maker’s specification and investigate the temperature difference between shaft and housing before changing clearance class.

Illustration for Schaeffler

Match lubricant viscosity to operating conditions

The lubricant’s first job is to separate moving surfaces where the operating conditions permit a protective film to form. Viscosity is a fluid’s resistance to flow, and it changes with temperature. In the lab we call this film formation; on your shop floor, it means keeping loaded metal surfaces apart as the bearing turns.

ISO 3448 assigns industrial liquid lubricants to viscosity grades based on their kinematic viscosity at 40 degrees Celsius. An ISO VG 68 oil, for example, has a nominal midpoint of 68 square millimeters per second at that temperature. That grade alone does not tell you its viscosity at the bearing’s actual operating temperature, nor does it establish additive suitability.

Use the equipment manufacturer’s required viscosity and the Schaeffler guidance for the bearing and application. Check the lubricant data sheet for viscosity at operating temperature, or use a suitable viscosity-temperature calculation supported by the available data. Speed, load, bearing size, and temperature all influence the film you can expect. A heavier oil can improve film thickness in some conditions, but it can also increase churning losses and operating temperature.

Application Note: On a gearbox with a bearing running hotter than the sump, use the bearing’s measured operating temperature when assessing viscosity, not just the temperature recorded on the oil reservoir. Confirm where and how that temperature was measured; a housing surface reading is not necessarily the lubricant temperature inside the bearing.

Grease consistency is not oil viscosity

Grease contains a lubricating fluid, a thickener, and often additives. The thickener helps retain the fluid, but the fluid supplies much of the lubrication. NLGI consistency grades classify grease by worked penetration, a measure of how readily a standard cone penetrates it. NLGI 2 describes consistency; it does not specify the base oil’s viscosity or prove that the grease suits a particular bearing.

For a grease-lubricated Schaeffler bearing, check the specified base-oil viscosity, NLGI grade, operating-temperature range, speed capability, and any requirements for water resistance or load-carrying additives. These properties must work together. A grease that pumps readily through a central system may still be wrong for the bearing if its base oil is too light or its temperature limit is inadequate.

Mixing greases is another avoidable risk. Different thickeners and additives can interact, changing consistency or performance. Do not assume compatibility because two cartridges share an NLGI grade. Obtain compatibility guidance from the lubricant suppliers and follow the equipment maker’s changeover procedure; cleaning out the old grease may be necessary.

Visual context for Schaeffler

Relubrication: quantity matters as much as interval

Too little grease can leave a bearing starved; too much can increase churning and heat. Schaeffler and the machine manufacturer may provide relubrication quantities and intervals for the specific arrangement. Use those instructions rather than filling every housing until grease appears at a seal. Some bearings are sealed and lubricated for their intended service life, and may not be designed for routine regreasing.

Application Note: For a motor bearing with a grease inlet and relief, identify the correct procedure before using the grease gun. Confirm that the relief path is serviceable and that the grease is the specified product. The correct amount and whether the motor should run during relubrication depend on the equipment instructions and site safety procedure.

Calibrate the grease gun’s output by weighing a known number of strokes. For example, if ten strokes deliver 15 grams, the average is 1.5 grams per stroke. A 6-gram instruction would then correspond to approximately four strokes with that gun and grease. Recheck when the gun or lubricant changes, and record the delivered amount rather than relying on an unverified stroke count.

Investigate damage before replacing the bearing

A failed Schaeffler bearing can provide evidence, but a damaged surface is not a root-cause diagnosis by itself. ISO 15243 classifies rolling-bearing damage and failures by visible characteristics and mechanisms. It gives an investigation a common vocabulary; it cannot reconstruct the machine’s history without supporting evidence.

Look for abrasive wear from particles, corrosion associated with moisture, and fatigue damage such as flaking of the raceway. Photograph both rings and rolling elements before cleaning them. Preserve a representative lubricant sample in a clean container, document its location, and note operating hours, temperatures, recent lubrication work, and any unusual noise or vibration.

Then check the surrounding system: seals, shaft and housing fits, alignment, lubricant delivery, and contamination sources. If repeated failures need a deeper review, provide the complete bearing designation and operating history to the equipment maker or Schaeffler technical support. Replacing the bearing without correcting the cause can put the same damage back on the maintenance schedule.

Updated · 2026-11-18 06:28
Feedback

No feedback yet — submit the first.

Submit feedback
© 2026 camshaftnow. All rights reserved. data-driven, published weekly ♥